PLACA BASE GIGABYTE INTEL 1151 I3 / I5 / I7 GA-H110-D3A

Artículo Borrado

Descripción

SOCKET : INTEL 1151
RAID: NO
FORMATO: ATX
CHIPSET: INTEL H110

CPU

    Support for 7th/6th Generation Intel® Core i7 processors/Intel® Core i5 processors/Intel® Core i3 processors/Intel® Pentium® processors/Intel® Celeron® processors in the LGA1151 package
    L3 cache varies with CPU

(Please refer "CPU Support List" for more information.)
Chipset

    Intel® H110 Express Chipset

Memory

    2 x DDR4 DIMM sockets supporting up to 32 GB of system memory
    * Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed.
    Dual channel memory architecture
    Support for DDR4 2400/2133 MHz memory modules
    Support for ECC UDIMM 1Rx8/2Rx8 memory modules (operate in non-ECC mode)
    Support for non-ECC UDIMM 1Rx8/2Rx8/1Rx16 memory modules
    Support for Extreme Memory Profile (XMP) memory modules
    * To support 2400 MHz or XMP memory, you must install a 7th generation processor.

(Please refer "Memory Support List" for more information.)
Onboard Graphics
Integrated Graphics Processor - Intel® HD Graphics support:

    1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz

Maximum shared memory of 1 GB
Audio

    Realtek® ALC887 codec
    High Definition Audio
    2/4/5.1/7.1-channel
    * To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
    Support for S/PDIF Out

LAN

    Realtek® GbE LAN chip (10/100/1000 Mbit)

Expansion Slots

    1 x PCI Express x16 slot, running at x16
    (The PCI Express x16 slot conforms to PCI Express 3.0 standard.)
    5 x PCI Express x1 slots
    (All of the PCI Express x1 slots conform to PCI Express 2.0 standard.)

* When two or more graphics cards are installed, be sure to connect the power cable from the power supply to the PCIE_12V_1 or PCIE_12V_2 connector to provide sufficient current to the system and prevent damage to the devices.
Storage Interface
Chipset:

    1 x M.2 connector (Socket 3, M key, type 2242/2260/2280 SATA SSD support)
    4 x SATA 6Gb/s connectors
    * Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA connectors.

USB
Chipset:

    4 x USB 3.1 Gen 1 ports (2 ports on the back panel, 2 ports available through the internal USB header)
    6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through the internal USB headers)

Internal I/O Connectors

    1 x 24-pin ATX main power connector
    1 x 8-pin ATX 12V power connector
    2 x PCIe power connectors
    1 x CPU fan header
    3 x system fan headers
    4 x SATA 6Gb/s connectors
    1 x M.2 Socket 3 connector
    1 x front panel header
    1 x front panel audio header
    1 x S/PDIF Out header
    1 x USB 3.1 Gen 1 header
    2 x USB 2.0/1.1 headers
    1 x Trusted Platform Module (TPM) header
    1 x Clear CMOS jumper

Back Panel Connectors

    1 x PS/2 mouse port
    1 x PS/2 Keyboard port
    1 x parallel port
    1 x serial port
    1 x D-Sub port
    2 x USB 3.1 Gen 1 ports
    2 x USB 2.0/1.1 ports
    1 x RJ-45 port
    3 x audio jacks (Line In, Line Out, Mic In)

I/O Controller

    iTE® I/O Controller Chip

H/W Monitoring

    Voltage detection
    Temperature detection
    Fan speed detection
    Overheating warning
    Fan fail warning
    Fan speed control
    * Whether the fan speed control function is supported will depend on the cooler you install.

BIOS

    2 x 64 Mbit flash
    Use of licensed AMI UEF